Cannon-instrument miniAV-LT Uživatelský manuál Strana 121
- Strana / 124
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
117
CANNON
®
miniAV-LT Low Temperature Automatic Viscometer with VISCPRO
®
Instruction & Operation Manual
Version 1.a— May, 2009; CANNON
®
Instrument Company
2139 High Tech Road • State College, PA 16803 • USA
CHAPTER
A
APPENDIX A–MULTIPLE UNIT
CONFIGURATION
Introduction
The miniAV-LT instrument is capable of being networked with the
controlling computer via available RS-485 connections. As many as four
miniAV-LT instruments may be connected to a single computer. Follow
the instructions in this appendix to complete assembly of the multi-unit
networking kit, available from CANNON
®
.
Kit components
The multi-unit interface kit contains an RS-232-to-RS-485 converter and
RJ-45 cables capable of networking up to four CAV Bath Units to a
single computer.
Procedure
Using the interface kit components, complete the multi-unit configuration
as follows:
Connecting components
NOTE The interface kit was designed for Bath Units placed in an adjacent
configuration. Custom configuration with longer RJ-45 cables is possible.
Make certain to install the VISCPRO
®
software on the controlling
computer. Complete all component assembly before proceeding with RS-
485 networking.
Completing RS-485 connections
CAUTION
1. Make sure the power is removed from the computer and all instru-
ments to be configured.
2. Locate the RS-485 converter and required RJ-45 connecting cable(s).
3. Attach the RS-485 converter directly to the computer via the standard
9-pin RS-232 connector. Then attach the longer RJ-45 cable from the
converter to the RS-232 connector on the serial communications
interface on the ear panel of the first miniAV-LT instrument.
- CONTENTS 1
- CALIBRATING THE miniAV 29 2
- USING THE miniAV SOFTWARE 37 2
- OPERATING, MAINTAINING 3
- AND SERVICING THE miniAV 73 3
- INTRODUCTION/INSTALLATION 5
- Measuring kinematic viscosity 6
- Safety cautions 6
- Installing VISCPRO 11
- software 11
- Running the software 12
- Checking configuration 13
- Logging in 14
- Checking Instrument Settings 14
- Prompt options 15
- Sample calibration constants 16
- Procedure 17
- The Calibration window 18
- Inserting the probes 20
- Inserting the thermometer 20
- Setting bath temperature 21
- Checking wash functions 22
- Training tube sensors 23
- Calibrating the miniAV-LT 23
- TESTING SAMPLES WITH THE 25
- VISCOMETER 25
- Running check standards 27
- Pausing a test 28
- Resuming a test 28
- Aborting a test 28
- Concluding a test 28
- The Machine Status window 29
- Group configuration 30
- Viewing test results 31
- Creating an analysis 31
- VI Matching with VISCPRO 32
- CALIBRATING THE miniAV-LT 33
- Training sensors 34
- Train Tube Sensors 35
- Standard tube calibration 36
- Selecting samples 38
- Comparing current/new data 38
- Saving a calibration 39
- USING THE miniAV-LT 41
- SOFTWARE 41
- Main Menu 42
- Security options 43
- Initial security setup 43
- Adjusting Security Settings 45
- Analyses Menu 46
- The Choose Analysis window 47
- Window Menu 48
- Configure menu 49
- Instrument Settings 52
- Tray Settings: Tube and Bath 54
- Bath Temperature 55
- Equilib. Tolerance 55
- Thermistors Radio Buttons 55
- Soak Time Units Radio Buttons 55
- Soak time 56
- Constants 56
- Tray Settings: Test 56
- Tolerance parameters 56
- Use greater 57
- Determinations 57
- Solvent rinse settings 58
- Max Solvent fill time(s) 59
- Solvent flush time(s) 59
- Tube tip soak time(s) 59
- Final dry time(s) 59
- Tray Settings: Advanced 60
- Maximum bulb 1 fill time(s): 61
- Maximum bulb empty time(s): 61
- Calibration 62
- Show Calibration Data 63
- Service menu 64
- Prewash option 67
- Trip Points Only option 67
- Selecting sample actions 69
- Sample actions 70
- Viscosity Action window 70
- The Viscosity Action window 70
- The Sample Action popup 70
- Copying Sample IDs 72
- Pasting Sample IDs 72
- Copying/pasting multiple IDs 72
- Saving Sample ID information 73
- Configuring the VI Matcher 74
- Configuration procedure 75
- Handling errors 76
- AND SERVICING THE miniAV-LT 77
- Solvent Dispensing System 78
- Emptying the Waste Receiver 79
- Viscometer tubes 80
- Temperature bath 81
- Ventilation 82
- Checking bath temperature 82
- Dual-solvent washing 83
- Solvent wash by computer 83
- Preventive maintenance 83
- ?etelpmoC ecnanetniamtneuqerF 84
- ANALYSIS CONFIGURATION 85
- Sorting analysis data 86
- Using the date filter 87
- Using the sample filter 88
- Resizing table columns 89
- Saving a current analysis 90
- Printing an analysis 90
- Exporting analysis data 91
- SAMPLE DATA TABLE 93
- Reporting options 94
- Report filter 96
- Selecting 96
- Modifying data presentation 96
- SAMPLE DATA EXPORT ANALYSIS 99
- Date/Sample filters 100
- Port Output Format filter 100
- Adding ports 100
- The Port Output Format window 101
- Configuring output 101
- Delaying serial output 101
- Selecting output data 101
- Adding a footer 102
- Adding a header 102
- Re-sending export data 103
- Port selection 103
- ERROR DATA EXPORT ANALYSIS 105
- Date filter 106
- Error Page filter 106
- The Error Page tab 107
- ERROR LOG TABLE ANALYSIS 111
- The Save Configuration window 113
- USING THE DATABASE 115
- Archiving old data 116
- Importing archived data 117
- REPLACEMENT PARTS LIST 119
- APPENDIX A–MULTIPLE UNIT 121
- CONFIGURATION 121
Související produkty a manuály pro Měřící nástroje Cannon-instrument miniAV-LT
(6 stránky)Moffat G58A manuals
Owner’s manuals and user’s guides for Cookers Moffat G58A.
We providing 1 pdf manuals Moffat G58A for download free by document types: User Manual
Komentáře k této Příručce